Q: What is UV Plus for Hardwood Decks?
A: UV Plus for Hardwood Decks is a penetrating wood stain and oil finish that beautifies and protects
exterior wood, providing a natural appearance. It is ideal for use on ipe, brazilian redwood, mahogany, meranti, massaranduba, teak and other exotic dense hardwoods. UV Plus for Hardwood Decks
contains fungicides and UV absorbers of the highest quality. It
does not form a surface film when properly applied and is not subject
to peeling and flaking. To recoat, just clean the wood
surface and reapply UV Plus for Hardwood Decks. No stripping or sanding is necessary.
Q: How long will it last?
A: On hardwood decks, UV Plus can be expected to last for 1-2 years. The time element will
vary depending on conditions such as sunlight, weather and direction of
exposure.
Q: I want to keep my wood looking natural? Should I
use a clear finish?
A: Clears with
no pigmentation do not
offer UV protection or color retention. Our products contain
Transparent Iron Oxide pigments which absorb UV radiation while
allowing visible light to pass through. This results in a finish that
highlights the natural beauty of the wood while still protecting it.
Q: After I applied UV Plus for Hardwood Decks, there are areas that are
shiny and tacky. What happened? How do I fix it?
A: This is
usually
caused by oversaturation of UV Plus for Hardwood Decks on the wood. Remember, the product must
be able to penetrate completely to work properly. Remove any excess
material promptly, 30-45 minutes after application.
If there are shiny, tacky areas due to overapplication and failure to remove excess product, scrub affected areas
with lacquer thinner or MEK solvent to soften excess material. Wipe
dry. If product has cured to the point that this does not correct the
problem, excess material must be removed by chemical stripping or
sanding. Dispose of clean up materials according to local, state and
federal regulations.
Another cause of
shiny tacky areas is applying the product to wood that is too damp. An
oil based product applied to a wet deck will not penetrate very well,
as the oil and water don't mix. Make sure that the deck is thoroughly
dry before applying any oil based product. Lumber that may appear to be
dry or dry at the surface can still have a high moisture content that
may "push" the oil back out if the boards are
heated up by the sun later in the day.
Q: Can UV Plus for Hardwood Decks be applied over another stain?
A: Yes, provided
the previous finish has sufficiently weathered to allow penetration of
UV Plus for Hardwood Decks. Before application, clean the surface with Wood & Deck Cleaner or sand to a new
surface.
Q: What is the proper temperature to apply UV Plus for Hardwood Decks?
A: We recommend
surface and air temperatures between 45F and 90F. Avoid application in
direct
sunlight on hot days. If the wood is hot to the touch, it is too hot to
apply UV Plus for Hardwood Decks.
Q: Why doesn't UV Plus for Hardwood Decks bead water?
A: Water beading
is accomplished by adding waxes or paraffin to the stain. These
additives do not
last very long and are not good permanent water repellents, in addition
to this they interfere with adhesion should you decide to paint over
the stain. That's why we don't use them in our products. UV Plus for Hardwood Decks fills the pores of the wood, providing
excellent water repellency that will last.
Q: The weather report predicts rain tomorrow. Can I
finish my deck today?
A: We wouldn't
recommend it. UV Plus for Hardwood Decks needs at least 24-48 hours to dry in good
conditions. If a newly stained deck is rained on, the rain can force
the stain up out of the pores of the wood, leaving a blotchy
appearance. It's best to wait until there is no precipitation expected
for 48 hours. In some regions, this may mean waiting for a different
time of year to finish the deck.
Q: Is UV Plus for Hardwood Decks suitable for vertical surfaces?
A: Yes, UV Plus for Hardwood Decks is an excellent choice for almost any exterior hardwood surface, including
vertical surfaces.
Make sure the
surface is clean, dry, and any previous coatings have either weathered
away or been removed. Do not use UV Plus for Hardwood Decks over paints or other film
forming coatings, it's designed to penetrate into bare or weathered
wood surfaces.
Q: I want a shiny finish. Can I put multiple coats
of UV Plus for Hardwood Decks on the wood?
A: No. The only
way to get a shiny surface on the wood is by using a multiple coat,
film forming finish. We don't
recommend clear film forming finishes on decks because they are
slippery when wet, they will eventually peel, and they are difficult to
maintain and recoat. When properly applied, a penetrating finish like
UV Plus for Hardwood Decks will not be shiny, it will have a natural, matte look.
Q: I have trim and other wooden surfaces that are made of cedar and pressure treated wood. Can I use the UV Plus for Hardwood Decks product on these?
A: Yes, UV Plus for Hardwood Decks can be used on other types of exterior wood, including cedar, redwood, pine, and pressure treated lumber. Keep in mind that the appearance of dissimilar woods will not be the same after applying the UV Plus, but generally it is very complementary.
